Search results

  1. 85squaredC10

    Carb to TBI Conversion

    Your very welcome. Good luck on your project. I can round up psrt numbers up you need them. Sent from my SM-G965U1 using Tapatalk
  2. 85squaredC10

    Carb to TBI Conversion

    I only have a single tank. On drivers side. I would think that as long as the line dimensions are the same, it should fit your application. Probably just reuse your current selector. But im not positive. Sent from my SM-G965U1 using Tapatalk
  3. 85squaredC10

    Carb to TBI Conversion

    I bought a new baffled tank....and in-tank fuel pump for a 1987 R10 with fuel injection. Used original gas lines for return style setup. In my case, I went with -6 lines mated to the 1/4" hard lines at the pump. And of course a fuel filter appropriate for the donor vehicle. For me it was a 93...
  4. 85squaredC10

    What have you done to your square lately??

    Sounds like I need a louder exhaust and a better stereo!!! Lmao Sent from my SM-G965U1 using Tapatalk
  5. 85squaredC10

    What have you done to your square lately??

    I am also looking into getting electric fans. Can't decide if I want one big fan or two smaller fans. Any thoughts? Sent from my SM-G965U1 using Tapatalk
  6. 85squaredC10

    New Member

    Welcome Sent from my SM-G965U1 using Tapatalk
  7. 85squaredC10

    What have you done to your square lately??

    Thanks for mentioning that. I'll have to check it out. Any advise for testing good/bad? Much appreciated. Side note: mine was new 2 years ago. Sent from my SM-G965U1 using Tapatalk
  8. 85squaredC10

    What have you done to your square lately??

    Mine sure is loud!! I couldn't imagine it being louder than it is!! Lol Sent from my SM-G965U1 using Tapatalk
  9. 85squaredC10

    What have you done to your square lately??

    So, why are they not equally spaced? Sent from my SM-G965U1 using Tapatalk
  10. 85squaredC10

    What have you done to your square lately??

    I was heating up my old rods to put on new pistons/pins....I ended up not being on center with this one. Is this going to cause an issue? If so, how do I get it off without damaging new parts? Sent from my SM-G965U1 using Tapatalk
  11. 85squaredC10

    What have you done to your square lately??

    Green thing has factory number stamped on it. Google it. My 85 has one. It is a speed sensor. Sent from my SM-G965U1 using Tapatalk
  12. 85squaredC10

    What have you done to your square lately??

    Looks like it may have been for a plow?. Pink wires running to the front look like heavy duty power wire. Sent from my SM-G965U1 using Tapatalk
  13. 85squaredC10

    What have you done to your square lately??

    Just replaced a coolant temp sensor today. Back to reading correctly! ......the little things! [emoji41] Sent from my SM-G965U1 using Tapatalk
  14. 85squaredC10

    What have you done to your square lately??

    Nice work!! I remember when I blew apart my harness for my 85 to 93 tbi swap. What a mistake!! I took 2 seasons to learn ALL the wiring diagrams and pinouts. It was a huge job, but I got it all done and it runs fantastic!! While I didnt want to take the time, nor did I want to learn wiring, I...
  15. 85squaredC10

    What have you done to your square lately??

    Dont forget to order the water pump!! .....its been a few days. [emoji16] Sent from my SM-G965U1 using Tapatalk
  16. 85squaredC10

    Steering Squeak

    Or, if your looking to remove the AC, just get a different single belt pulley for the PS pump and it should be good. Sent from my SM-G965U1 using Tapatalk
  17. 85squaredC10

    What have you done to your square lately??

    1978 C10 Fleetside 250 I6 3 speed on the tree. Engine rebuild. Happening now. I got the Engine/Trans removed, separated, and now cleaning it enough to take it apart without a ton of grease everywhere. It was really bad, as you can see from the photos. Power washed it yesterday. Will begin the...
  18. 85squaredC10

    Tanks

    Exactly...my swap had me running my pump dry 3 or 4 times before I learned of the tank differences. Sent from my SM-G965U1 using Tapatalk
  19. 85squaredC10

    One side sagging

    Mine sags 1" on the passenger's side. It is worn out/original 85 leaf spring sag! Lol. Sent from my SM-G965U1 using Tapatalk
  20. 85squaredC10

    Tanks

    If your using the harness from your donor vehicle, it will all hook up fine for the fuel injection, provided your using the compatible pump for that style harness. But you WILL need the ECU (computer) from the donor vehicle to run it. The 84 computer will not run the new harness. I'd buy an ECU...
  21. 85squaredC10

    Tanks

    Yes, carburetor setups will work with baffled tanks for fuel injection, but not the opposite way around. Sent from my SM-G965U1 using Tapatalk
  22. 85squaredC10

    tbi issues

    Sounds like the throttle return spring in the throttle body is weak/broken. Replace that or add a throttle return spring like in a carburetor setup and you should be good. Sent from my SM-G965U1 using Tapatalk
  23. 85squaredC10

    Carb to TBI Conversion

    I did a swap from a 85 350 quadrojet carburetor to 93 350 TBI. I absolutely love it. No more starting issues...obd tells me if there are issues...better gas mileage (not much more, but noticable)..I couldnt be happier. Did it all myself as my first swap ever.....it was a hard and tedious...
  24. 85squaredC10

    95 TBI 350 Compatible w/ 90-91 tbi?

    I swapped a 93 350 tbi into my 85 C10. It has a serpentine belt and tensioner setup. I would assume that you would have to run the newer setup of the 95 you have or change the front accessory brackets to you old setup. I'm my experience, it all has to do with the accessory brackets. Run the...

Latest posts

Forum statistics

Threads
42,343
Posts
914,036
Members
33,845
Latest member
aaron06
Top