Search results

  1. C10MixMaster

    Quadrajet Choke missing?

    The electric choke opens at one speed so the down side is on really cold days it sometimes opens to fast (stalls out)and on warm days opens to slow (hi idle). The thermostat coil choke heats up with engine temperature, so warm day its already off or barely on and opens quickly and on a cold day...
  2. C10MixMaster

    What have you done to your square lately??

    Its the price you pay when you have an anti oil administration in the White House.
  3. C10MixMaster

    What have you done to your square lately??

    just about have the transmission rebuilt for the truck. Added a shift kit boost valve and corvette servo. Decided to wire the lockup converter through the 3rd gear switch this time so I should have lock up in 3rd and 4th
  4. C10MixMaster

    Big 10 Catalytic Converter, lol.

    No egr no cat was a requirement when I was looking for my truck. 77 heavy half fit the bill. Only down side is it still had an air pump
  5. C10MixMaster

    ‘83 K5/4” lift/4WD: Still in need of header fitment recommendations for new crate SBC SP350 w/“D” port heads/angled plugs.

    I'm running hedman 69099 dport headers on a zz4 350 with dport angle plug heads, plugs clear fits well ,I like the ball collector flange I can't say I'm in love with the quality of the welds probably pretty average for a budget header . I'm running it in a 2wd so can't tell how well it clears a...
  6. C10MixMaster

    What have you done to your square lately??

    Took it to the drag strip and smoked the transmission.
  7. C10MixMaster

    Parking Light Puzzle

    Weird light problems always check your grounds
  8. C10MixMaster

    What have you done to your square lately??

    changed out the wheel studs that were too short fronts were simple press in the rears I had to drill and cut to size
  9. C10MixMaster

    What have you done to your square lately??

    finally installed the headers that have been sitting under the bench for about a year now.
  10. C10MixMaster

    Carburetor rebuild help!

    Yes it's your secondary metering rod cam. It mounts on the shaft between the secondary air valve plates/valves
  11. C10MixMaster

    Whats you gas mileage on your squarebody truck?

    You should have your gmsquarebody membership revoked lol
  12. C10MixMaster

    What have you done to your square lately??

    modified a set of 87 fuel tanks for my 77
  13. C10MixMaster

    Steering Column Interchange

    I built the column in my truck using the bottom from the 77 and the top is from a 93? OBS I think I had to fabricate the dimmer switch rod because of the length, so a lot of the pieces interchange between them. In retrospect finding a square body tilt column would have made more sense.
  14. C10MixMaster

    What have you done to your square lately??

    Got a new starter the old one was making a weird chattering noise. Upgraded to new permanent magnet gear reduction starter. New battery the old one was 6 yrs old didn't trust it and rebuilt the batt cables. The new starter is over 10# lighter.
  15. C10MixMaster

    How to send power to window switch for testing?

    the later system alternates the power and ground to make it go up or down
  16. C10MixMaster

    What have you done to your square lately??

    Found a fuel leak, I guess I know what my next project is..
  17. C10MixMaster

    Q jet loses prime.

    Leaky well plugs were a problem on the earlier carbs from the 60's. G.M. changed the way they installed them and most of the problems went away. You can pull the carb add some fuel or spray carb cleaner and observe the well plugs to see if they leak. I think well plugs a blamed too often...
  18. C10MixMaster

    What have you done to your square lately??

    Just the regular standard ignition lx301 not the blue streak . above 3k was were it was having issues.
  19. C10MixMaster

    What have you done to your square lately??

    I finally got to play with my distributor machine. Sure beats leaning over the fan blades. Charted the different combinations of plates and springs that I had. One thing I noticed was when running a distributor with the oe module you can here the plugs go ZZZZZZZZZZZZZZZZZZZZZ, the distributor...
  20. C10MixMaster

    What have you done to your square lately??

    I have added a drain plug to all my trucks , I would love to get ahold of the bean counter that talked GM out of putting drain plugs from the factory :mad:
  21. C10MixMaster

    Homemade and modified tool thread

    homemade distributor machine
  22. C10MixMaster

    Some timing questions (experiencing some spark knock)

    vacuum advance is working. the fact you can advance the mechanical advance and take a a pic of it advanced shows there is something wrong there. it should spring back on its own. You might have to remove the distributor and disassemble the shaft, I think these 2 parts are rusted or gummed up...
  23. C10MixMaster

    Some timing questions (experiencing some spark knock)

    that doesn't sounds right. 30 is a lot for initial timing. If you rev the engine how much advance do you get? 36 should be about max for initial and mechanical not including vacuum advance. Things I would check advance springs Missing broken?, advance seized , advance weights badly worn...
  24. C10MixMaster

    What have you done to your square lately??

    resealed the A6 A/C compressor, hopefully no more oil line on the hood. Out with the old ceramic seal in with a new modern seal .
  25. C10MixMaster

    Emissions sticker

    not rpo but window sticker with current mods

Latest posts

Forum statistics

Threads
42,136
Posts
909,933
Members
33,636
Latest member
ehef
Top