Search results

  1. 8

    Another 700R question

    Well, found the problem. Starter drive gear hitting the flywheel. I have a 3 HP mini starter on it. There is clearance between them, maybe 10 thousands. I had done put 1 spacer between the starter housing, it needs 2. Starter works great, sounds good, but you put it in reverse and it barely hits...
  2. 8

    Another 700R question

    It's in the forward gears also, drove it today. Yesterday, it done it soon as I put it in reverse, all the way out of the garage until I put it in drive and then it quit. I drove it about 3 miles today and as I slowed down and made a U turn to go back I could hear it lightly. It done it before...
  3. 8

    Another 700R question

    I've got a noise, sounds like it's in the front part of the trans but I can't really tell. It sounds like a real bad header gasket or exh leak. Only does it when I put it in reverse, when I go to drive it goes away. I lost hearing in my right ear and it is really hard for me to pinpoint where...
  4. 8

    700R4 questions

    No, just the shift kit and the servo. Wanted to get the lock up working. I'm getting a 350 turbo built, already have the spacer, but I wanted to get the truck on the road and keep this trans for awhile if I could.
  5. 8

    700R4 questions

    Thanks, they had some good info. I ordered a external switch set up. My solenoid is a 1 wire, since I don't need any other wiring in the trans, except for lock up in 4th, I thought about using 1 of the 2 prong sensors in the trans in the 4th gear port and doing it all internally. Figured I'd try...
  6. 8

    700R4 questions

    Anyone got a diagram of the oil pressure switch deal? That sounds like my best bet. Also, where the 4th gear port is and what pressure switch to get.
  7. 8

    700R4 questions

    Right now my truck, 84 K10, has the 700R4 in it. I'm going to put a mild shift kit in it and do the servo update, corvette servo. My trans has 3 wires on the plug on the left side of the trans, what controls the lock up on this year truck? The reason I ask is that there are wires cut and things...
  8. 8

    Step Bumper Brackets

    I'll post this on here in hopes it's seen. I'm pretty sure it was on this site where I read where someone needed step bumper brackets. I had a set on my 84 that I'm using, but the rear step bumper I bought has a set also. They have the extra bracket that bolts to the bottom of the frame. I have...
  9. 8

    Front driveshaft question

    Thanks, I thought since my 84 isn't lifted it might work. Don't need any vibration. Looking at it in the truck, it don't really look like it has enough angle to require a double joint.
  10. 8

    Front driveshaft question

    Will these 2 driveshafts interchange? Mine, with the double joint is wore out where the slip yoke is, slines are shot. They both have the same bolt pattern, it'd also be nice to get rid of that double joint.
  11. 8

    Brake Box

    Yes, brakes on both axles and I'm referring to the blue wire. Just wondering if there is a better way than just running a 14 ft piece of wire back to the trailer plug. With a large load and dual axle brakes, I'm concerned about heat .
  12. 8

    Brake Box

    I would think this is electrical, got a question on a trailer brake box. First off, I haven't installed one in years that you didn't just plug in, all the newer models are plug and play. I'm going to install one in my 84 K10, wouldn't it be better to run a relay some way than just running a...
  13. 8

    How To Refurbish Your Dashpad

    Mine looked like yours, I spent a ton of time on it but it actually cracked in 3 places moving it around.
  14. 8

    Parts(misc, trim, wire, etc...)

    That's bad that they cut them. What do you want for them? I've seen the pouches, just thought I might get lucky on a used one. Thanks, you can PM me if you want.
  15. 8

    BBC pulleys

    PM sent 74 shortbed.
  16. 8

    Parts(misc, trim, wire, etc...)

    I need a blue left side arm rest, 1 map pocket, and the carpet for the lower part of the front doors if you have that. Need a useable dash pad to, but they are nonexsistant it seems.
  17. 8

    Large Parts Stash

    I got 2 dual head light bezels missing the center trim if you still need them. Pay for the ride.
  18. 8

    Weiand tunnel ram and carbs

    Thought maybe someone on here may have a hotrod or gasser project and need these. Need the money to finish up my truck. I have a Weiand Tunnel Ram, like new, 2, Holley 650 DP"s, all gone through with Quick Fuel kits, 6 AN fittings in carbs, Brand new breathers, Brand new side mount linkage...
  19. 8

    Seals for vent assy

    Thanks for the heads up.
  20. 8

    3 spd shift indicator

    Sorry, didn't think about taking one.
  21. 8

    Door Panels

    I may have to try this deal with the bed liner. I dyed one of the panels today and you can see alot of imperfections, and thats after sanding, scuffing and you name it. I'll try it on 1 and see what it looks like, got to get more dye first.
  22. 8

    3 spd shift indicator

    Got the indicator today and installed it in the cluster. It was the complete indicator, and a pretty nice piece. Hope this saves somebody a $$.
  23. 8

    Seals for vent assy

    I'll recheck and see. Those pics they have are kind of hard to figure out. They have a decent price on the seals, I've only found a few dollar difference. Plus that's the only time I've seen the rivets. Also I checked my vent assy and I got that rivet in the top they show in the thread you...
  24. 8

    Gas tank stuff

    Get the 3/8's hose for fuel injection. It's a lot better hose. Some of this regular fuel hose now is crap. A lot of it has a plastic like liner in it.
  25. 8

    Seals for vent assy

    LMC has the 2 piece seal kit for $50, they also have a repair kit, #12, that looks like it has the rivets in it, and what I hope is that rubber seal, #13 , that goes in the glass for the handle or latch to pass through.

Latest posts

Forum statistics

Threads
42,061
Posts
908,225
Members
33,540
Latest member
irishgoodbye
Top