Search results

  1. J

    New Project.... need advice on motor swap

    If I can find the Google link to the article where they dynod it after an intake and headers and gain 40 horsepower I will put it up that is where I got the info. They did four or five test the first one was only an intake a 4-barrel carburetor and headers the second one they changed out the...
  2. J

    New Project.... need advice on motor swap

    Intake/carb are for that vortec motor. Stock the motor is 260hp/330tq as it sits in a 96-01 truck. In my truck with no cats, no smog, that intake l, carb and headers. I am hoping to make around 300hp with nothing else. Sent from my SAMSUNG-SM-G930A using Tapatalk
  3. J

    New Project.... need advice on motor swap

    I am in sort of the same boat, got a 305 that is lacking in power and want to drop in a Vortec crate engine. I am going with the L31-R from summit and this intake/carb kit. https://m.summitracing.com/parts/cmb-03-0197/applications?prefilter=1 Sent from my SAMSUNG-SM-G930A using Tapatalk
  4. J

    Motor swap list...

    Changed up carb/intake for a ligtld better of a deal and the distributor for melonizdd gear for roller cam. 1: Engine:** https://www.summitracing.com/parts/nal-12530283 2: Carb and Intake: https://www.summitracing.com/parts/cmb-03-0197 3: Distributor:**...
  5. J

    Motor swap list...

    Lmc carries a fuel pump module that may work. Yea was debating on how to do lockup, right now its unplugged. Tcc solenoid is bad and will stay in lockup even after if downshifts, would stutter and die at redlights. Barely been driving it, although once I replace the shift indicator and get...
  6. J

    Motor swap list...

    Plan for fuel is to put a tank in rear where spare tire was and run all new fuel line with an inline pump. Likely run high pressure line since I may eventually swap over to fitech efi. Will have to read on oil pressure saftey switch and how to trigger the fuel pump on I guess.....all new...
  7. J

    Motor swap list...

    Link should work now: Its a 1987 Chevy Silverado R10, sensors would be oil pressure and temp, don't really know what others I need to swap over. I have throttle position, temp, oil pressure, ignition control module, map sensor, idle air control valve, EGR valve and electronic spark control...
  8. J

    Motor swap list...

    Getting fairly close to the beginning process of ordering a motor, have a few I am looking at and after throwing around several ideas the last few months. I am thinking the Vortec L31-R motor is going to be the way to go.* The price difference from the older style is not that much more for a...
  9. J

    What have you done to your square lately??

    Re-wired all lights in rear, previous owner has a rats nest back there. He tapped in to wires for trailer light, but all he did was cut the insulation and left wire intact. Then just stripped and wrapped the trailer wire around it.....no electrical tape, butt connector, solder nothing. So got...
  10. J

    What have you done to your square lately??

    Wash and wax today, came out pretty good but still got a ways to go on it. Sent from my SAMSUNG-SM-G930A using Tapatalk
  11. J

    Cam suggestions L31-R

    Thank you Sent from my SAMSUNG-SM-G930A using Tapatalk
  12. J

    Cam suggestions L31-R

    I am going to be installing a Vortec crate engine and fitech in my truck this fall and was hoping to get cam suggestions for the stock motor as it comes. Searching now for something with usable power and torque. Only plans so far is longtube headers, summit stage 1 intake manifold or similar...
  13. J

    86 K10 5.3 swap

    Subscribing. Getting ready to start putting togethor the parts needed for my trucks motor build. Going to start with fuel tank/lines then start getting motor/trans/harness togethor. Sent from my SAMSUNG-SM-G930A using Tapatalk
  14. J

    What have you done to your square lately??

    New fender and working on new door hinges. Old dented fender Old driver door hinge New carpet ready to go in Sent from my SAMSUNG-SM-G930A using Tapatalk
  15. J

    How To Refurbish Your Dashpad

    Trying this out now, mine is pretty bad. Actually I cannot cut back far enough to reach vinyl that does not crack. Still going to attempt it, if it doesn't come out well enough I will order a replacement. So far I have sprayed some foam to find out i did not cut vinyl back enough. May just...
  16. J

    Post a picture of your Rim & Tire

    Boss 338's - 22x9.5 - 265x30R22 tires - installing 2.5/4 drop soon and trying to swap these for some 18s or 20s soon. Or buy some rims and sale these after the first of the year. Sent from my SAMSUNG-SM-G850A using Tapatalk

Latest posts

Forum statistics

Threads
42,116
Posts
909,463
Members
33,611
Latest member
RNFL
Top