Search results

  1. T

    1990 3/4 ton Duramax swap

    I would have to guess that would need to be fabricated. I suggest joining the squarebody duramax swap group on Facebook.
  2. T

    1990 3/4 ton Duramax swap

    The frame will be fine. Precision fabrication plus has the majority of the stuff needed. Be ready to drop a ton of cash and either be able to fab stuff or drop even more cash to pay someone else to do it. I’m balls deep in my swap, hemorrhaging money with the faintest glimmer of an ending in...
  3. T

    Sanden A/C compressor

    I have a brand new sanden ac compressor from vintage air that I bought to use with an ls swap but have switched to a duramax swap and this one won’t work with it. I am thinking 200 shipped.
  4. T

    power step / board

    Bringing this one back up. With saddle tanks I don’t know if amp steps would be possible but would the Aires actiontrac steps possibly work?
  5. T

    Three link

    What are the complications in converting a 2wd frame to 4wd with a three link coil over conversion? Before anyone says buy a 4wd frame I want to do coil overs anyhow so shouldn’t it be as simple as keeping good geometry or is there that large of a difference in the frames?
  6. T

    6.6 duramax

    Well I haven’t posted many updates but I decided to jump off the deep end and purchased a compound turbo kit from pusher intakes. Not sure how long till it arrives but we shall see if it fits with ease or will I need a big fcking hammer.
  7. T

    Front vs rear winch

    Well I am resurrecting this one from the dead. I have settled on a front winch mount and was looking at the behind bumper winch mount (bbwm). Does anyone have this setup?
  8. T

    6.6 duramax

    @Vbb199 I will but the going is slow. If only I had an unlimited supply of money.
  9. T

    6.6 duramax

    Tell me about it and gas prices are so much cheaper.
  10. T

    6.6 duramax

    Ya, cause the price of diesel is what is going to break the budget on this project.
  11. T

    6.6 duramax

    Well she is in.
  12. T

    6.6 duramax

    Need to buy a spot blaster to clean up the block some for paint and then I will stuff her into the engine bay. I will post a picture of that when I get there, then I will have to see if my radiator/intercooler choice is going to work.
  13. T

    6.6 duramax

    Bringing this one back up. I’m getting close to putting the duramax into the square.
  14. T

    Modern steering column swap?

    Where can a guy find an older column with the wipers on the column and a tilt? Short of scouring the wrecking yards.
  15. T

    Modern steering column swap?

    Could you elaborate more on what is different? Just trying to see what this can of worms could turn into.
  16. T

    Modern steering column swap?

    Has anyone attempted to swap a modern steering column into a square? I was thinking about finding a 2007 ish column/wheel setup so I could have tilt/telescope, column shift and if I can figure it out using the wiper controls also. The big question is if the shaft can be made to work with the...
  17. T

    Amp Power Steps on a K5 solved.

    Would your setup clear saddle tanks in a pickup setting?
  18. T

    6.6 duramax

    Does anyone know if a compound turbo setup will fit in a squarebody? Seems like the only thing that could get in the way is the second battery? Hoping to knock out the old crossmember stuff and install the new square max mounts next week on my five day truckation!
  19. T

    In the throes of completion SQUAREMAX L5P

    I’ll second that let’s see it.
  20. T

    Chevy 6.0 with 4l80e

    That is a fact. Only reason I am selling this one is because of the duramax swap I am doing now instead.
  21. T

    Chevy 6.0 with 4l80e

    mr clean you sound like quite the tool posting stuff like this. Did I say my feelings were hurt? If you don’t like the price move on it’s as simple as that. I don’t know anything about the motor other than what was posted, I bought it from a reputable shop and never got around to doing anything...
  22. T

    6.6 duramax

    My squaremax brackets showed up today. Everything looks really well put together now I just need to find the time to pull the old motor setup out and to get everything setup.
  23. T

    Chevy 6.0 with 4l80e

    Man you can’t leave well enough alone can you. I didn’t really care the first time around but come on. All I am doing is listing it for a little less than I paid for the whole setup. If you can get one for cheaper all set up in this same complete package good on you but I don’t really see it...
  24. T

    LS swap

    Exactly most of us have a full time job and if you factor in the cost of your time your 2,000 dollar setup just went over 4,000 and you lost all the time associated with getting it going. If I had unlimited hours I would smelt the aluminum and steel it takes to make a motor but alas I don’t have...
  25. T

    LS swap

    If you can put this package together for 2,000.00 sign me up.

Latest posts

Forum statistics

Threads
41,849
Posts
903,432
Members
33,362
Latest member
Dhatch84
Top