Search results

  1. EvilGenius

    AC Delco AM/FM Radio For Sale

    This radio should work. I plugged it into the stock harness and it powered on and put out static. Couldn't test the FM function as the antenna wasn't plugged in so no reception. Comes with support bracket. $50 plus shipping. Willing to meet locally in the Detroit metro. I'm planning on attending...
  2. EvilGenius

    Windshield seal gap

    Is a gap like this normal at the corner of the windshield? This is a new seal and lock strip on an old windshield. Not sure if it leaks since the build is still in progress and it hasn't seen any weather.
  3. EvilGenius

    Driver kick panel trim options

    So I have a non-AC cab with the two fresh air vents in the kick panels. I'm looking for a "silverado" kick panel trim that covers the entire kick panel and has the fixture for the fresh air valve controls. I currently have trim with the air valve controls but it isn't full height and I have a...
  4. EvilGenius

    Bed Bar out of a 77 step side

    Know these are sought after and not real common anymore so thought I'd put it out there for the people looking for one. Not mine, just saw it and wanted to share. https://annarbor.craigslist.org/pts/d/ann-arbor-bed-bar-for-c10-or-k10/7130358922.html
  5. EvilGenius

    SBC 350 Fan shroud mounting

    I'm having a difficult time figuring out how the fan shroud is supposed to be mounted on to the core support. I have a 3 core radiator and a 2 piece shroud. The bottom half of the shroud has been trimmed some by the PO to allow it to be removed with messing with the fan. The shroud doesn't seem...
  6. EvilGenius

    4wd indicator light wiring

    Finally installing a lot of the wiring into my rebuild. When looking at the sub harness for the 4wd indicator light the white wire that runs from the tcase switch is cut. I'm not sure where it should go. I've dug through the wiring diagrams and it seems it should go to a 4wd indicator relay...
  7. EvilGenius

    700R4 Cooler Line Routing

    I recently purchased and installed pre-bent cooler lines from Inline tube. They look great and seem like a quality product. Here is the issue though, I can't figure out how they should be run. I have them installed now, but they are tight up against the headers and that cannot be correct. Does...
  8. EvilGenius

    Cab to Fender Seal?

    I was recently pulling parts off of my other cab and pulled off what appear to be a foam seal between the cab and the front fenders. Was this a factory option and are they necessary? I can't recall seeing them on any of the parts sites like LMC. Pic of it on the cab: Pic of one removed...
  9. EvilGenius

    ISO Engine Bay Pics

    I'm looking for pictures of line routing in the engine bay. Fuel lines, tranny cooler lines, brake lines, and power steering lines. I don't seem to have many good pictures of how these lines are routed in the engine bay and would like some reference pictures as I reassemble. I'm cutting and...
  10. EvilGenius

    Rear Brake Line Hanger

    Looking for the brake line hanger that is riveted to the frame on the passenger side above the rear differential. Mine was removed via torch and was tossed at some point. Please see the picture below for reference (Source: google images)
  11. EvilGenius

    K10 front brake pads wrong thickness?

    I've been rebuilding my front axle over the last couple months and am finally putting the new calipers and brake pads on. However, when I go to put the caliper on, the outer brake pad seems to be too thick. The caliper bolt guides don't have enough clearance to get over the lip on the threads of...
  12. EvilGenius

    WTB 1981+ 4x4 Trans Tunnel

    I have a 1983 c10 cab that has been used for a donor in my k10 rebuild. To clear the transfer case, I need the higher center floor section used in 4x4s. After some research it looks like 1981-1983 or 1984-1987 floor pan sections would work. I've searched in my area for a parts yard that has...
  13. EvilGenius

    Firewall Repair Advice

    I have a bit of a rust issue on my firewall from what I assume is rain water running down from the cowl. Is there a good way to go about repairing this? It looks like the side panel is spot welded on and might be removable. The pictures aren't the best, but the hole extends all the way to the...
  14. EvilGenius

    Manual Doors and Rear Roll Pan

    I have a set of super clean manual doors. They were flawless until one of the front fenders nicked it when they were being pulled off. So now they have a chip in the paint on one door. The chip in the passenger door I mentioned: I also have a rear roll pan for sale. Both of these...
  15. EvilGenius

    Replacing Fuel Tank Straps

    Any good methods to remove the tank strap rivets? My strap broke off when I pulled the tank mount off and I need to remove the remnants of the old strap before I can clean up the mount and paint it. Also should the lower part of the tank mount be welded to the upper part like this?
  16. EvilGenius

    Front shackle bushing wrong size?

    I bought some new front shackles off rock auto and I'm wondering if the bushings that were included have a outer lip that is too deep. When I put the shackles on the frame it was difficult to get the nut on as there was almost no thread available past the bushing. When putting the spring on...
  17. EvilGenius

    Help rolling up power windows with cab removed

    Are there any methods out there for rolling up the power windows on a cab that is completely off the frame? I did a stupid and left the windows down once I started my frame work. Cab won't be going back on the frame for a decent amount of time and having the windows up would be nice.
  18. EvilGenius

    Best replacement body and engine mounts

    Since I'm doing a frame up resto I will be replacing my engine and body mounts. In fact the old body mounts are already in the trash because they were so bad. Any advice on whether to go with rubber mounts or polyurethane? Any brands to avoid? I haven't had to to do this before so any input is...
  19. EvilGenius

    Best option for new suspension similar to stock

    I'm looking for new suspension parts that would have the same ride height as the stock suspension in a k10. I have a relative that has offered to trade me a new 4in lift kit for something similar to stock because his 4in lift kit ended up being much too tall for his bogger. Ride stiffness...
  20. EvilGenius

    Joined and have been lurking a while. Finally saying hi.

    Hello everybody. I bought a k10 scottsdale sans motor back in January and got a complete but needing some love k10 silverado last month. I've been looking around here to prepare myself for when I dig into my project. Lots of great info on here. I'll be sure to post a build thread with pictures...

Latest posts

Forum statistics

Threads
42,029
Posts
907,714
Members
33,522
Latest member
Laqota
Top