Search results

  1. TJ805

    Steering Column Swap

    After reading RetroC10Sport's killer post, I wonder how these columns are identified. For example, I need a 238-237A. Will this be stamped on the column? I've searched the numbers and get nothing pertinent. I'm looking to put a tilt wheel in my '73 K-10 and do not want a column that's longer...
  2. TJ805

    NP205 Driven gear

    What seals this from the inside? Rubber o-rings? Flat nylon? Pressure fit? It appears to have place for seal, but mine has none. The search window, as usual produced nothing, so I'm asking anyone who might know. -Thanks
  3. TJ805

    RTV to stop yoke leak on 205 front output?

    Should I just apply it to the washer and torque it down? I found a rubber star seal for my rear 32 spline, but front is 10 spline. Any help is appreciated. The large main seal was replaced btw...
  4. TJ805

    WTF?

    Cleaning up my Dana 44 front and found a bondo like substance on the driver side of the carrier. It was about the size of a quarter and on a casting. It was light color and had a stubborn green paint like substance mixed in. Hard to believe that it belonged there so I removed it. Green stains on...
  5. TJ805

    79 K-10 parts on my 73

    I've been picking a 79 for parts and I wonder if the front and rear leaf springs will work on my '73. I believe the 73 to be stock with two leaves in front, but I actually have 8 in the rear. They're not in the greatest condition, but I like how the truck sits. Do the 79 fronts have different...
  6. TJ805

    Dana 44 Axel bearings?

    Been trying to get this front end cleaned up and it's been humbling. My current issue is the right side axle. I pulled it out to inspect and clean and upon reassembly, it seems to turn rough. Hearing some metal on metal. I put it in dry, should I grease it up? The knuckle rubs on the tube and I...
  7. TJ805

    Front outer races not press fit on '73 K-10

    Got what I believe to be small bearing front hubs and the outer races on both sides are loose enough to fit by hand. Inners are perfectly snug. I'm using Timken set 45's and Set 37's. Has this happened to anyone? Should I be worried? Any short term fixes? I'd love to hear any and all info.
  8. TJ805

    "73 K-10- Help with Timken Inner Bearings

    LM603049 or LM104949? Getting conflicting info. Any help is appreciated... Set 37 inner and set 45 outer?
  9. TJ805

    '73 K-10 Seat Replacement Options

    Has anyone used a newer seat or buckets for their 70's truck? Any recommendations on what will bolt on with minimal mods? Pics? Thanks!
  10. TJ805

    I need Advice on '73 K10 Suspension

    This truck rides on 33" tires with no rub or clearance issues, but appears to have no lift. is this possible? Any advice on upgrades? Just looking to stay stock and have good general performance. No major romping planned...
  11. TJ805

    Flowmaster 40's

    WHAT THE HELL DID I FIND IN THESE MUFFLERS? Got 'em for $10 each shook all this woodlike stuff out and soaked em in Jasco. They seem like new, but the mystery remains. This is not wood. The cellular composition is completely symmetrical and gridlike...
  12. TJ805

    73 K10 Seats

    Hi, I'm so cramped against the steering wheel. I'm wondering what seats work for conversion. Has anyone had any luck with swap-outs from other models or aftermarket? Hoping to get something from the junkyard... -Thanks, TJ
  13. TJ805

    12 Bolt Pinion Bearing Pre-Load

    When I went to change the pinion seal, the pinion nut was finger tight. I planned on using my torque wrench to get an idea of where it was at, but now have to guess. Wheels are on the truck and I have no plans to remove them or the axles. I'd like to get it as close as possible for the time...
  14. TJ805

    Rear Pinion Seal

    Is this gap acceptable? I used moderate force, but didn't want to damage the thing. Unfortunately I didn't compare it's depth to the one I removed. How hard should I have to hit this momma? All help is appreciated...
  15. TJ805

    Help ID this rear end...

    It's on a "73 K10 that I was told was "all original". Fortunately I got a deal, so no big. Pics are all I could find. No visible stamp on axle tube. I think it's a corporate, but really want to know if it is posi. I will eventually get into it, but hope someone can give me info based on these...
  16. TJ805

    Chevy OEM Hood?

    I've had a few disagreements about this hood being OEM. The front detail is the point of contention. I say that it is an aftermarket design. Can anyone verify?

Latest posts

Forum statistics

Threads
43,936
Posts
946,050
Members
35,982
Latest member
jake26104
Top