Coolant Temp Gauge Question

Disclaimer: Links on this page pointing to Amazon, eBay and other sites may include affiliate code. If you click them and make a purchase, we may earn a small commission.

Kilian

Full Access Member
Joined
Mar 25, 2018
Posts
166
Reaction score
24
Location
Wisconsin
First Name
K
Truck Year
1983
Truck Model
C2500 hopefully converting to K2500
Engine Size
350
The coolant temp gauge on my 83 GMC C2500 is pegged at max temp, I'm assuming the problem is in the gauge and not the sender. What do I need to replace to get the temp back working? Can I just replace the gauge or do I have to swap out the whole instrument cluster. Thanks!
 

Blue Ox

Turning Diesel Fuel Into Fun
Joined
Mar 27, 2018
Posts
4,831
Reaction score
10,633
Location
LI-NY
First Name
Derek
Truck Year
MCMLXXXV
Truck Model
K20HD
Engine Size
6.2L
A maximum reading can be caused by a faulty sender or a short to ground. Find the sender and pull the wire to see if the reading changes. It should show minimum temp with the wire disconnected. If it does the sender is probably NG. If it remains pegged the wire may still be shorted to ground somewhere.

If the gauge turns out to be bad you can just replace the gauge.

*Sorry, said pressure, meant temp. Fixed it.
 
Last edited:

Blue Ox

Turning Diesel Fuel Into Fun
Joined
Mar 27, 2018
Posts
4,831
Reaction score
10,633
Location
LI-NY
First Name
Derek
Truck Year
MCMLXXXV
Truck Model
K20HD
Engine Size
6.2L
Yes sir. You are correct. I wasn't going to get in to typing a novel. But it's been sitting unanswered all day so I thought I'd give it a boost. Also, I don't think it's common for the gauges themselves to fail, but that's only my limited experience.
 

78C10BigTen

Full Access Member
Joined
Apr 12, 2017
Posts
15,475
Reaction score
23,682
Location
pennsylvannia
First Name
Ted
Truck Year
1978
Truck Model
C10 BIG TEN
Engine Size
350
Yes sir. You are correct. I wasn't going to get in to typing a novel. But it's been sitting unanswered all day so I thought I'd give it a boost. Also, I don't think it's common for the gauges themselves to fail, but that's only my limited experience.
Well to my knowledge (that they havent been replaced) all my 40 year old gauges still work so.... (even the clock)
 

Kilian

Full Access Member
Joined
Mar 25, 2018
Posts
166
Reaction score
24
Location
Wisconsin
First Name
K
Truck Year
1983
Truck Model
C2500 hopefully converting to K2500
Engine Size
350
Thanks for the replies. I will check out the sender to see if that is the issue.
 

Kilian

Full Access Member
Joined
Mar 25, 2018
Posts
166
Reaction score
24
Location
Wisconsin
First Name
K
Truck Year
1983
Truck Model
C2500 hopefully converting to K2500
Engine Size
350
Checked the sender wire tonight and I have 12 volts at the connector. No change in the gauge when sender wire is disconnected. I plan on checking out the gauge next.
 

chengny

Full Access Member
Joined
Feb 22, 2012
Posts
4,086
Reaction score
1,008
Location
NH
First Name
Jerry
Truck Year
1986
Truck Model
K3500
Engine Size
350/5.7
Checked the sender wire tonight and I have 12 volts at the connector. No change in the gauge when sender wire is disconnected. I plan on checking out the gauge next.


You are pegged high correct? What you need to do is look for is a short to ground in the DK GRN lead that runs from the gauge to the sender. It comes out of the loom behind the distributor and runs along the LH valve cover to up near the front. Then it drops down to the sender. Start at the sender end and inspect the wire all the way back to where it goes into the loom. Look closely for breaks/chafing in the insulation. If there is a short to ground in this lead, it is generally going to be in the engine compartment. Even if a ground exists in the DK GRN lead, you will still read 12 VDC at the sender. Also, disconnecting the lead from the sender - when a short to ground exists - won't cause the gauge to come off the high end.
 

Snoots

Full Access Member
Joined
Jan 23, 2013
Posts
8,158
Reaction score
15,957
Location
Georgia
First Name
Roger
Truck Year
1973
Truck Model
Jimmy Sierra
Engine Size
350
You can 'Ohm out' the sender.

For Truck Years: 1979 - 1990

The Temp Gauge Needle Should Point to:
Left Line (Cold) when sender resistance = 1,365 Ohms
Middle Line when sender resistance = 96 Ohms
Right Line (Hot) when sender resistance = 55 Ohms
 

NICK K

Junior Member
Joined
Oct 22, 2017
Posts
6
Reaction score
4
Location
San Bruno CA
First Name
Nick
Truck Year
1985
Truck Model
SIERRA 1500 STEP SIDE
Engine Size
5.0
I have the same problem on my 85 GMC. I disconnected the wire from sender and gauge went to zero. replaced the sender and the gauge read correctly for a little while but now is pegged to the hot side again
 

chengny

Full Access Member
Joined
Feb 22, 2012
Posts
4,086
Reaction score
1,008
Location
NH
First Name
Jerry
Truck Year
1986
Truck Model
K3500
Engine Size
350/5.7
I have the same problem on my 85 GMC. I disconnected the wire from sender and gauge went to zero. replaced the sender and the gauge read correctly for a little while but now is pegged to the hot side again

A false high reading is usually an indication that the gauge's sensing leg is shorted to ground. Trace the DK GRN lead that runs along the valve cover and connects to the sender.

This is just a WAG but it might be the case that, the original high reading was caused by a short to ground in the sensing lead rather than a faulty sender. But, during the sender replacement procedure you moved the wire in such a way that the short circuit was temporarily broken. Then after a while, the conductor again came in contact with the engine - and now you are showing high again.
 

NICK K

Junior Member
Joined
Oct 22, 2017
Posts
6
Reaction score
4
Location
San Bruno CA
First Name
Nick
Truck Year
1985
Truck Model
SIERRA 1500 STEP SIDE
Engine Size
5.0
thanks
previous owner has left me a few wiring puzzles
 

Latest posts

Forum statistics

Threads
41,851
Posts
903,501
Members
33,365
Latest member
rossivey
Top