Recent content by swilson143
-
LQ4 swapped 91 Suburban for auction
I've really enjoyed building and driving this Suburban, but it's time it goes to a new home. https://bringatrailer.com/listing/1991-gmc-suburban-4/- swilson143
- Thread
- Replies: 1
- Forum: eBay & Craiglist Listings
-
running boards, nerf bars, step bars !!!
Nfab doesn't stock them, but they're available for squarebodies. They're just made to order after you've made the purchase. Very happy with mine.- swilson143
- Post #36
- Forum: Aftermarket Accessories
-
Cab Underside Treatment
I used UPOL epoxy spray liner for my wheel wheels. Affordable, available on Amazon, comes with spray gun. Super easy to spray, just make sure your masking job is well done!- swilson143
- Post #11
- Forum: Paint and Body
-
GMC Suburban Rear Emblems
https://www.ebay.com/itm/152078865228 I bought this one on Ebay. Not identical as my original, but very close. Installed with 3M double sided tape- swilson143
- Post #5
- Forum: Paint and Body
-
Replica OEM wheels
Thanks for that, had no idea they were available in 8 lug- swilson143
- Post #9
- Forum: Wheels and Tires
-
18” Rallys? They sure look right on this Custom Deluxe!
Looks so good!- swilson143
- Post #8
- Forum: Wheels and Tires
-
Proper process for painting most of your interior parts
Good info, Thanks for posting!- swilson143
- Post #23
- Forum: Interior
-
-
CA legal LS swap
Sadly, I'm selling the Suburban. Needed a diesel truck for all the towing I do and can't afford to have both vehicles. https://bringatrailer.com/listing/1991-gmc-suburban-4/- swilson143
- Post #30
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
CA legal LS swap
To disable VATs, turn on electric fan controllers, etc you either need a laptop and a program like HP Tuners, or you can just pay a shop to program your PCM for you. If you're only programming one vehicle, one time, it's much cheaper to pay a shop to do the programming. In your state I imagine...- swilson143
- Post #25
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
CA legal LS swap
I did the procedure using HP tuners. It was extremely vague. When you choose the process in their software, it tells you what to do ... Start the motor, increase revs over 2-3 second until the engine hits fuel cut off, then release the throttle and turn the engine off You don't get any...- swilson143
- Post #22
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
CA legal LS swap
Those are pretty slick switches. The one I used is identical to your last photo, except not labeled- swilson143
- Post #19
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
CA legal LS swap
The guy that programed my PCM initially disabled the PRNDL switch which you have pictured above. Turns out having that disabled prevents you from being able to do a crank relearn!! I was fighting my engine swap for a couple of months trying to figure out why I was getting false misfires...- swilson143
- Post #17
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
CA legal LS swap
Just used a momentary switch. For those looking to do this, Tow/haul needs to be turned on using HP tuners. If my memory serves me, it's actually called tranny performance mode in HP tuners. Then you'll need to run a wire inside the cab from your PCM (pin Blue-71) to a momentary switch. The...- swilson143
- Post #12
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
-
CA legal LS swap
Good for you. I like that stuff too. Now do me a favor and don't post here unless you have something constructive to say that's related to this thread.- swilson143
- Post #11
- Forum: Engine Swaps (Gas) LS, Vortec, LT1 , etc.
