Recent content by roundhouse

  1. R

    Brake lights out

    You’ll need a good test light and a helper If the hazards work It’s not the wiring back to the light Probabaly in the switch A lot of times the signal switch under the steering wheel goes bad It controls the brake lights and the signals to the rear It took me 9 hours and several trips...
  2. R

    Sm465 swap

    Meh If it’s just one ear it will Probabaly be fine to run it Also, if the top pivot on your clutch pedal is worn out bad enough that new bushings won’t fix it You can use a automatic brake pedal and flip it over and cut off the bottom half of the pedal and bolt the bottom half of your clutch...
  3. R

    New steering box and now this....

    Redhead makes the best steering boxes for square bodies And they have a seal on the adjustment bolt. And the warranty is void if you turn the bolt. They adjust it right and bench test it before they ship it to you.
  4. R

    stepside fuel filler hose and vent

    We bent up a coat hanger for a pattern and spent about two hours at an auto parts store looking at all the radiator hoses and taking them out and test fitting them. Finally found some that fit I might can find the numbers on them somewhere in a couple days Everyone says you can’t use...
  5. R

    So, the 350 was rebuilt, huh ?????

    If the seller doesn’t have a receipt , the engine didn’t get rebuilt . As y’all know an engine or trans rebuild is big money, and comes with a warranty, anyone who gets an engine rebuilt would save the receipt Incase the needed the warranty. If they don’t have a receipt, they are lying, so...
  6. R

    Bed floor rubber mat

    Makes it a lot easer to cut.
  7. R

    Wheel Adapters

    Not that hard to swap on 8 lug spindles on the front and an 8 Lug axle in the back of thats he look you really want
  8. R

    1990 K5 Jimmy ZERO Rust-130k-Original Paint-Interior-350TBI

    Perhaps potential buyers are like you and don’t want the flipper to be making a fat profit out of their pocket ? Bring a Trailer might be a good place I’ve seen some nice squares being good money there But you have to have lots of high quality pics and a cold start video and be available to...
  9. R

    Square Body owner new to Forum

    When you find an axle , pull the cover and inspect the gears for wear, and verify the ratio. Ask the seller if they have already removed the cover to inspect, if they have not, and don’t want you to, then they don’t know what the ratio is , or they don’t want you to see how bad the gears are...
  10. R

    Aftermarket a/c

    We used vintage air In the 76 K10 and in the 65 Falcon wagon. It’s a good kit , not too hard to install We have a LS engine so was a little more expensive since we had to buy the kit to put the compressor in a different location than stock on the LS
  11. R

    Adding convertor (s). Yes, I said adding.

    You could use some short tube headers
  12. R

    Adding convertor (s). Yes, I said adding.

    Make sure to install plenty of heat shielding
  13. R

    2000s hydroboost into a square

    The 6.2 diesel squares had a hydro boost from the factory Should be a bolt in deal
  14. R

    Bulkhead / Firewall Connector

    Everything is made in communist China Don’t worry, the carona won’t be on it Really funny watching everyone in the airport wearing masks while gripping the rubber handrail of the escalator I bet there more germs on it than in the toilet bowl of the airport bathroom We embargo Cuba...
  15. R

    Bulkhead / Firewall Connector

    I had a lot of problems with the connector not making contact internally I just cut the wires and used high quality connectors thru a grommet and eliminated the connector altogether It’s just there for quick assembly at the factory
See more

Latest posts

Forum statistics

Threads
42,129
Posts
909,784
Members
33,625
Latest member
narr
Top