Forums
New posts
Search forums
What's new
New posts
Latest activity
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
nvrenuf
Full Access Member
·
From
Mobile, Al.
Joined
Jul 30, 2010
Last seen
43 minutes ago
·
Viewing latest content
Posts
1,724
Reaction score
1,936
Points
113
Find
Find content
Find all content by nvrenuf
Find all threads by nvrenuf
Latest activity
Postings
About
nvrenuf
reacted to
Strick's post
in the thread
What lift kit did i just buy
with
Like
.
K30 stuff is hard to come by in Central NC. Get out in the western mountains & see them more. I'm parting out an 80 which is also the...
Yesterday at 11:08 PM
nvrenuf
replied to the thread
What lift kit did i just buy
.
Trivia; the first couple of years of K30’s used the short 2wd style hangers with blocks.
Yesterday at 10:09 PM
nvrenuf
reacted to
Strick's post
in the thread
What lift kit did i just buy
with
Like
.
4wd hangers drop down farther which lifts the frame & negates the use of a lift block. I figured this out when I was a young pup. I've...
Yesterday at 10:05 PM
nvrenuf
replied to the thread
What lift kit did i just buy
.
Yeah, I’ve seen it done with 2 and 4wd hangers (I doubt most folks realize there’s a difference).
Yesterday at 9:07 PM
nvrenuf
reacted to
Strick's post
in the thread
What lift kit did i just buy
with
Like
.
Isn't the old trick for a flip is to use the front 2wd hanger in place of the rear 4wd & then flipping the swing? HS
Yesterday at 9:05 PM
nvrenuf
replied to the thread
What lift kit did i just buy
.
My bet is that’s a typical 4” kit without the shackle flip. The flip brackets look well built but homemade, I haven’t seen any built...
Yesterday at 7:29 PM
nvrenuf
reacted to
Turbo4whl's post
in the thread
Tach wire and relay
with
Like
.
Electronic spark control will use the tach port. It usually will have a short piggyback empty plug you can use for the tach signal. If...
Tuesday at 6:06 PM
nvrenuf
replied to the thread
Tach wire and relay
.
I see it now. In the first post I didn’t noticed the loose connector hanging, I was just looking at the cap. At this point, you’ll have...
Tuesday at 5:47 PM
nvrenuf
replied to the thread
Tach wire and relay
.
There is not a wire connected to the distributor cap at the tach slot, it’s a small 1/4x1/4 slot that should have a connector like the...
Tuesday at 5:08 PM
nvrenuf
replied to the thread
Transmission grinds going into L or R
.
This ^^ Normal operation. If it’s always done it but now it’s worse, the clutch likely needs to be adjusted.
Tuesday at 4:37 PM
Loading…
Loading…
Latest posts
S
Soon to be new member…
Latest: SirRobyn0
8 minutes ago
Introduction
What have you done to your square lately??
Latest: DoubleDingo
19 minutes ago
Garage
I need a donut
Latest: DoubleDingo
Yesterday at 11:27 PM
Tech Discussion
Jumping in - 86 k10 long bed (first square body)
Latest: Strick
Yesterday at 10:54 PM
Introduction
What lift kit did i just buy
Latest: Strick
Yesterday at 10:28 PM
Lifted & Off-Road Systems
Forum statistics
Threads
42,116
Posts
909,451
Members
33,611
Latest member
RNFL
Members
Top