Recent content by lowblackc10

  1. lowblackc10

    seat swapping?!

    I actually swapped out my bench for the buckets, console and floor shifter from a 79 cutlass. They sit a bit lower than the bench but they are much more comfortable and I like the way it seems to match the rest of the interior.
  2. lowblackc10

    dropping the tired th350 for an m21.

    Well that's a pretty good point. My main issue is pedals but I'll do some more looking around at local yards. Its been kind of tough trying to find any with this winter we've had in in cny, and a standard pickup is proving to be hard to find around here. Other than that and a yoke I should have...
  3. lowblackc10

    dropping the tired th350 for an m21.

    Thanks for the input guys, I have put some thought into it and I decided to keep the th350 for the time being and maybe save the Muncie for a hotrod project in the future. Between the tall first gear and what are probably 3.08's in the rear I just don't want to have to run it like that, being my...
  4. lowblackc10

    th350 and transgo 1-2 kit

    Does anybody have information on this kit? I bought it but the instructions are somewhat vague and I would kind of like a second opinion on what to do. My truck is an 84 c10 swb 5/6 drop. Its has a non-lockup th350 with a mild stall, what should I do as far as my kit goes? It will see some...
  5. lowblackc10

    c10 front disc problem

    Hi all, I have an 84 c10 that I got shortly after sitting in a barn for ten years. So I replaced most of my brake lines including the front rubber ones as well as rotors, pads, calipers, master cylinder, wheel cylinders, shoes and drums. My issue is that my driver side front brake seems to be...
  6. lowblackc10

    dropping the tired th350 for an m21.

    Okay, that's good to know because there is a 1 ton 3+3 with a th400 at my uncles, but if that is different, maybe my local yard will have something. Thanks again for all the input and saving me a trip.
  7. lowblackc10

    dropping the tired th350 for an m21.

    The reason I have to change the yoke is that my m21 is a 1970-74 and has the 26 input and 32 output spline shaft, same as the m22. I was under the impression that it was a m22 until I looked the numbers up a years or so ago. Most m21's did come with the 27 spline output like you say though, Im...
  8. lowblackc10

    dropping the tired th350 for an m21.

    So I got my truck on the lift today and measured the length from the transmission mount to the end of the tailstock. I have an H-pipe in my way from getting an exact measurement but it seems that they are both the same length. I thought it should be since I pulled the autotragic out of a '79...
  9. lowblackc10

    dropping the tired th350 for an m21.

    Awesome! Thanks for the input but I should have specified that I have the 26 spline input and 32 spline output, I'm not 100% on the casting numbers and measurements but i will get it on the lift on the next few days and measure things up. With the age of it I would guess its probably manual...
  10. lowblackc10

    dropping the tired th350 for an m21.

    Hi all, I'm new to this site and have a few questions. I have an early 70's muncie m21 that I want to put into my 84 c10. It is a car transmission and I"m wondering will the car bellhousing and clutch fork work in my pickup? Would it be compatible with a fluid clutch? If not am I better off just...
See more

Latest posts

Forum statistics

Threads
42,312
Posts
913,492
Members
33,810
Latest member
Garcjay
Top