Recent content by 1979 K10

  1. 1

    Tank replacement for EFI

    Thanks for the pics. I'll have to lookup the weatherpak female connector or just hard wire it. Do you use all rubber line rated for fuel injection or off brand like evil energy? Gates 42195653 3/8 for feed...
  2. 1

    Tank replacement for EFI

    @SquareRoot I really appreciate your help! I updated my previous post and will probably go with: Delphi FE0114 pump Dorman 692044 sender? - Seems like this is the only sendor for a fuel pump. Or order a TBI pump housing assembly and swap out the pump?
  3. 1

    Tank replacement for EFI

    Looking at rockuto for a 97 k1500, these pumps are offered: '87 Fuel senders
  4. 1

    Tank replacement for EFI

    I think I’ll order a 87 tank for the driver side and use the vortec truck in tank fuel pump if it will support my 500 hp motor. Or will use this pump sometime mentioned here https://www.summitracing.com/parts/aei-11569 I’ll just bypass the valve and wire and plumb the driver side tank as a...
  5. 1

    Tank replacement for EFI

    Hmm, I seriously considered the pro flo 4 system but I just put a rpm intake on my new motor and got the sniper 2 complete kit for $1500 out the door. I guess I could resell the Holley pump if I don’t use it. The sniper 2 kit I got came with a Holley external regulator...
  6. 1

    Tank replacement for EFI

    just purchased sniper 2 kit which comes with external pump, regulator and hose. My 79 K10 has the dual 16 gallon side tanks. I just installed a 500hp blueprint 400 crate engine. I’m guessing I can’t use the 96-99 vortec in-tank fuel pumps? If I go with the external Holley pump, can I just run...
  7. 1

    How much HP will a th350 handle? New motor!

    In cab startup with Blueprint 400, longtube headers, true dual exhaust with Dynomax super turbo mufflers.
  8. 1

    How much HP will a th350 handle? New motor!

    Have had the Blueprint 400 installed for over a year. Haven't put but 1k miles on it as it stays parked for the most part during the winter and I have other vehicles. https://www.summitracing.com/parts/mll-bp4002ct1 It runs very strong and the ol TH350 is holding up so far so good. I replaced...
  9. 1

    Np203 part time conversion?

    79 Chevrolet K10 Blueprint 400 sbc startup Stock 400 and truck walkaround 1979 K10 Silverado walk around 2" lift front 3" lift rear 33" BFG KO2 Not to derail thread but I just put a blueprint sbc 400 in it so will see how long that part time conversion holds up going from 185hp /...
  10. 1

    Np203 part time conversion?

    There used to be 2 part time kits available to change the np203 from full time to part time. I did the cheaper mile marker kit which you could convert the tcase from full to part time while installed in the truck. Took an hour or two but super easy and straightforward, you just swap a gear which...
  11. 1

    NP203 to NP208 swap?

    Posted in Np203 part time conversion? thread https://www.gmsquarebody.com/threads/np203-part-time-conversion.37080/
  12. 1

    NP203 to NP208 swap?

    There used to be 2 part time kits available to change the np203 from full time to part time. I did the cheaper mile marker kit which you could convert the tcase from full to part time while installed in the truck. Took an hour or two but super easy and straightforward, you just swap a gear which...
  13. 1

    New here, building a 82 K10

    USA1 better than LMC or pretty much resell parts from the same supplier? My truck needs cab corners, quarter corners, lots of interior if I want to make it mint.
  14. 1

    pulls to right quickly if you let go wheel,zero tire wear for 18yrs.

    Could be a sticking driver side caliper or deterioration of driver rubber brake line (deteriorate from the inside and act as a check valve which allows brake fluid to caliper but doesn’t release pressure when off brake pedal.)
  15. 1

    How much HP will a th350 handle? New motor!

    My truck is 4WD and the crossmember supports the transfer case. I believe it’s as easy as moving the stock crossmember back 3” and drilling new holes in frame. Issue is you have to shorten rear driveshaft and lengthen front driveshaft. I’ve hear of some people moving motor 2-3” forward. But...
See more

Latest posts

Forum statistics

Threads
42,281
Posts
912,884
Members
33,780
Latest member
joshuars
Top